DIY Arduino Battery Capacity Tester - V1.0

Parts Required :

1. Arduino Nano (Gear Best / Banggood )

2. 0.96" OLED Display ( Amazon / Banggood )

3. MOSFET - IRLZ44 ( Amazon )

4.Resistors ( 4 x 10K , 1/4W ) ( Amazon / Banggood )

5. Power Resistor ( 10R, 10W ) ( Amazon )

6. Screw Terminals ( 3 Nos) ( Amazon / Banggood )

7.Buzzer ( Amazon / Banggood )

8.Prototype Board ( Amazon / Banggood )

9. 18650 Battery Holder ( Amazon )

10. 18650 Battery ( GearBest / Banggood )

11. Spacers ( Amazon / Banggood )

Tools Required :

1. Wire Cutter / Stripper ( Gear Best )

2.Soldering Iron ( Amazon / Banggood )

Instrument Used :

IMAX Balance Charger ( Gearbest / Banggood )

Infrared Thermometer Gun ( Amazon /Gearbest)

Schematic :

To understand the schematic easily, I have drawn it on a perforated board also. The positions of the components and wiring are similar to my actual board. The only exceptions are the buzzer and OLED display. In the actual board, they are inside but in the schematic, they are lying outside.

The design is very simple which is based on Arduino Nano. An OLED display is used to display the battery parameters.3 screw terminals are used for connecting battery and the load resistance. A buzzer is used for giving different alerts. Two voltage dividers circuit is used to monitor the voltages across the load resistance. The function of the MOSFET is to connect or disconnect the load resistance with the battery.

Working :

Arduino checks the battery condition, if the battery is good, give the command to switch ON the MOSFET. It allows current to pass from the positive terminal of the battery, through the resistor, and the MOSFET then completes the path back to the negative terminal. This discharges the battery over a period of time. Arduino measures the voltage across the load resistor and then divided by the resistance to find out the discharge current. Multiplied this by the time to obtain the milliamp-hour ( capacity ) value.

Voltage Measurement

We have to find the voltage across the load resistor. The voltages are measured by using two voltage divider circuits. It consists of two resistors with values 10k each. The output from the divider is connected to Arduino analog pin A0 and A1.

Arduino analog pin can measure voltage up to 5V, in our case the maximum voltage is 4.2V (fully charged). Then you may ask, why I am using two dividers unnecessarily. The reason is that my future plan is to use the same tester for the multi-chemistry battery. So this design can be adapted easily to achieve my goal.

Current Measurement :

Current (I) = Voltage ( V ) - Voltage drop across the MOSFET / Resistance (R)

Note: I am assuming the voltage drop across the MOSFET is negligible.

Here, V = Voltage across the load resistor and R = 10 Ohm

The result obtained is in amperes. Multiply 1000 to convert it into milliamperes.

So maximum discharge current = 4.2 / 10 = 0.42A = 420mA

Capacity Measurement :

Stored Charge ( Q ) = Current ( I ) x Time (T ).

We have already calculated the current, the only unknown in the above equation is time. The millis() function in Arduino can be used to measure the elapsed time.

The selection of load resistor depends on the amount of discharge current we need. Suppose you want to discharge the battery @ 500mA, then the resistor value is

Resistance ( R ) = Max Battery Voltage / Discharge Current = 4.2 /0.5 = 8.4 Ohm

The resistor needs to dissipate a bit of power, so size does matter in this case.

Heat dissipated = I^2 x R = 0.5^2 x 8.4 =2.1 Watt

By keeping some margin you can choose 5W. If you want more safety use 10W.

I used 10 Ohm, 10W resistor instead of 8.4 Ohm because it was in my stock at that time.

Here MOSFET acts like a switch. The digital output from the Arduino pin D2 controls the switch. When 5V (HIGH) signal is fed to the gate of the MOSFET, it allows current to pass from the positive terminal of the battery, through the resistor, and the MOSFET then completes the path back to the negative terminal. This discharges the battery over a period of time. So the MOSFET should be chosen in such a way that it can handle maximum discharge current without overheating.

I used an n-channel logic level power MOSFET-IRLZ44. The L shows that it is a logic level MOSFET. A logic level MOSFET means that it is designed to turn on fully from the logic level of a microcontroller. The standard MOSFET (IRF series etc) is designed to run from 10V.

If you use an IRF series MOSFET, then it will not fully turn ON by applying 5V from Arduino. I mean the MOSFET will not carry the rated current. To tuned ON these MOSFETs you need an additional circuit to boost the gate voltage.

So I will recommend using a logic-level MOSFET, not necessarily IRLZ44. You can use any other MOSFET also.

To display the Battery Voltage,discharge current and capacity, I used a 0.96" OLED display.It has 128x64 resolution and uses I2C bus to communicate with the Arduino. Two pins SCL (A5), SDA (A4) in Arduino Uno are used for communication.

I am using U8glib library to display the parameters.First you have to download the U8glib library .Then installed it.

If you want to get started in to OLED display and Arduino , click here

The connections should be as follows

Arduino --> OLED

5V --->Vcc

GND -->GND

A4----> SDA

A5----> SCL

To provide different warning or alert, a piezo buzzer is used.The different alerts are

1. Battery Low Voltage

2.Battery High Voltage

3. No Battery

The buzzer have two terminals, the longer one is positive and the shorter leg is negative.The sticker on the new buzzer have also " + " marked to to indicate the positive terminal.

The connections should be as follows

Arduino --> Buzzer

D9--> Positive terminal

GND--> Negative terminal

In the Arduino Sketch, I have used a separate function beep() which sends the PWM signal to the buzzer, waits for a small delay, then turns it off, then has another small delay. Thus, it beeps once.

5 More Images

In the previous steps, I have explained the function of each of the components in the circuit. Before jump to make the final board, test the circuit on a bread board first.If the circuit works perfectly on the bread board,then move to solder the components on the protype board.

I used 7cm X 5cm prototype board.

Mounting the Nano : First cut two rows of female header pin with 15 pins in each.I used a diagonal nipper to cut the headers.Then solder the header pins.Be sure the distance between the two rails fits the arduino nano.

Mounting OLED Display : Cut a female header with 4pins. Then solder it as shown in picture.

Mounting the terminals and components : Solder the remaining components as shown in pictures

Wiring : Make the wiring as per schematic.I used colored wires to make the wiring, so that I can identify them easily.

After soldering and wiring,mount the standoffs at 4 corners.It will provide sufficient clearance to the soldering joints and wires from the ground.

The software doing the following tasks

1. Measure voltages

Taking 100 ADC samples , adding them and averaging the result.This is done to reduce the noise.

2. Check the battery condition to give alert or start the discharge cycle

Alerts

i) Low-V! : If the battery voltage is below the lowest discharge level ( 2.9V for Li Ion )

ii) High-V! : If the battery voltage is above the fully charged condition

iii) No Battery! : If the battery holder is empty

Discharge Cycle

If the battery voltage is within the low voltage ( 2.9V )and high voltag (4.3V),discharge cycle start.Calculate the current and capacity as explained earlier.

3. Display the parameters on the OLED

4. Data logging on serial monitor

Download the Arduino Code attached below.

Attachments

• Battery_Capacity_Tester-V1.0.ino
  Download

To test the circuit, first I charged a good Samsung 18650battery using my IMAX Charger. Then put the battery into my new tester. To analyze the entire discharge process, I export the serial data to a spreadsheet. Then I plotted the discharge curve. The result is really awesome. I used a software named PLX-DAQ to do it. You can download it here.

You can go through this tutorial to learn how to use PLX-DAQ. It is very simple.

Note: It works only in Windows.

After few testing I conclude that the tester result is quite reasonable.The result is 50 to 70mAh away from a branded battery capacity tester result.By using a IR temperature Gun, I measured the temperature rise in the load resistor also,the maximum value is 51 deg C.

In this design the discharge current is not constant, it depends on battery voltage.So the discharge curve plotted is not similar to the discharge curve given in the battery manufacture data sheet.It only support a single Li Ion Battery.

So in my future version I will try solve the above short comings in the V1.0.

Credit : I would like to give credit to Adam Welch, whose project on YouTube was inspired me to start this project.You can watch his YouTube video.

Please suggest any improvements.Raise a comments if any mistakes or errors.

Hope my tutorial is helpful.If you like it,don't forget to share :)

Subscribe for more DIY projects. Thank You.